STAIN PREVENT ELIMINATES MINERALS Quality
controlled formula. A mixture of water conditioners which makes pools minerals
and metals inactive.Contains chelation agent. Liquid concentrate.pH 0.75.
Prevents corrosion of the pool equipment. Eliminates and prevents tartar build up
on the inner surfaces of the pool without affecting the pH of water.
Buy30-21121-11
Alum Clarifier - 1 kg
Item ID: (30-21100-11) Brand: IPG
CLARIFIER ALUM makes pool water sparkling
clear.
CLARIFIER ALUM is especially effective for pool water that is very
cloudy or coloured by the presence of metal.
PREVENTIVE
TREATMENT:
For perpetually sparkling clear pool water, use Klear Sok
or Action Cube.
Fill the pool above skimmer. Adjust
parameters at recommended levels. Free available chlorine:
1.0 – 2.0
ppm pH: 7.2 – 7.8
2. Stop the filtration system and put the filter in
recirculate (or whirlpool) position. Start the system.
3. Add 400 g of
CLARIFIER ALUM per 10,000 L of pool water. Sprinkle the required quantity
directly on the surface of water.
4. Recirculate pool water for 4 to 6
hours. Stop filter and allow water to remain undisturbed preferably overnight to
allow debris to deposit to bottom of pool.
5. Remove residue by putting
filtration system in drain (or waste) position and vacuuming.
6. Readjust
water parameters. Use pH+ to increase water pH, since using CLARIFIER ALUM
decreases pH. Use approximately 200 g of pH+ per 500 g of CLARIFIER ALUM to
reach pH levels of 7.2 to 7.8.
Buy30-21100-11
Phos Defence - 1 L
Item ID: (30-21136-11) Brand: IPG
When added phosphates are reduced to very low levels.
Buy30-21136-11
Pool Sparkle - 1 L
Item ID: (30-21080-11) Brand: IPG
POOL SPARKLE
CONCENTRATED
CLARIFIER
30-21080
Provides clear and
sparkling water.
A very powerful formula.
POOL SPARKLE
enhances the effectiveness of the filtering system by coagulating microscopic
particles to larger masses.
The solids thus formed are deposited at the
bottom of the pool or are captured by the filtration system.
POOL
SPARKLE is not affected by chlorine, does not contain alum and is efficient in any
pH condition without modification.
POOL SPARKLE is
used while the filtration system is working.
1. Initial treatment: add 50
mL of POOL SPARKLE per 10,000 L of pool water. Pour around the pool.
2. After 8 hours of filtration, if the maximum recommended pressure has
been reached, clean the filter medium by backwashing the filtration system.
3. If needed, clean the bottom of the pool.
4. Adding 50 mL of
POOL SPARKLE per 10,000 L of pool water on a weekly basis will help keep pool
water clear and sparkling.
5. For very cloudy water due to high
hardness levels, airborne dust or dead algae: pour 250 mL of POOL SPARKLE per
10,000 L of pool water.
Buy30-21080-11
Sparkle Drop - 1 L
Item ID: (30-21084-11) Brand: IPG
SPARKAL DROP
FLOCCULATING
AGENT
30-21082
FLOCCULATING AGENT
for cloudy Swimming Pool Water.
SPARKAL DROP is an inorganic
polymer that readily forms soluble or insoluble complexes with anionic materials
present in water.
This polymer facilitates the floculation of floating
debris, dead algae and minerals that cause cloudy, brown or green water.
These debris are then easily vacuumed.
SPARKAL DROP does
not affect pH, chlorine or any other type of sanitizer.
NOTE: Application of this treatment in rainy weather is not recommended.
Using SPARKAL DROP with a diatomaceous earth filter is not recommended.
1. Fill the pool above the skimmer.
2. Stop the
filtration system and put the filter in recirculate (or whirlpool) position. Start the
system.
3. Add 80 mL of SPARKAL DROP per 10,000 L of pool water.
Pour the required quantity evenly over the entire surface.
4. Recirculate
pool water for 4 to 6 hours in order to disperse the product. Stop filter and allow
water to remain undisturbed preferably overnight to allow debris to deposit to the
bottom of the pool.
5. Remove residue by putting filtration system in
drain (or waste) position and vacuuming.
6. Don't forget to clean the
filter before returning to regular operation by first performing a backwash. Use our
CLEAN filter cleaner for any kind of traditional filter.
Buy30-21084-11
Ci Pro Stain Prevent - 4 L
Item ID: (30-24121-04 ) Brand: IPG
Ci Pro Stain Prevent - 4 L
Buy30-24121-04
Ci Pro Clarifier - 4 L
Item ID: (30-24080-04 ) Brand: IPG
Ci Pro Clarifier - 4 L
Buy30-24080-04
Terminator - 1 L
Item ID: (30-21110-11 ) Brand: IPG
When you start your pool, at springtime or during the regular season, shock treatments are required and a waiting period is necessary until the residual value has dropped to the recommended levels of 1 to 3 ppm.
If you wish to decrease the sanitizer residual rapidly, use TERMINATOR and take advantage of your pool immediately. TERMINATOR will not affect the colouring of vinyl, cement or fibreglass pools.
Application:
To reduce sanitizer level before using your pool:
1. Test the sanitizer level. If readings are higher than 3 ppm, add TERMINATOR in small quantities (50 ml per 10,000 L of pool water) to reduce high sanitizer level back to acceptable levels 1-3 ppm. 2. Wait for 1 hour. 3. After adding TERMINATOR, check water's pH and adjust to 7.2-7.8 if necessary.
RECOMMENDATION: Do not exceed dosage. Use in small increments and test water between additions of this product
Buy30-21110-11
Meta Ban - 1.2 kg
Item ID: (30-21335-11) Brand: IPG
Treats all water sources.
A granular sequestrant that helps remove quickly water discoloration in swimming pools from the presence of metals such as manganese, iron and copper.
Can also be used to remove staining on every type of swimming pool surface due to metal.
Concentrate quality formula
Does not alter pH and is compatible with any types of sanitizers
Do not make water cloudy
May be used for the whole season with all types of filters:
Sand Cartridge Diatomaceous earth filter
Application
1. Adjust pH between 6.8 - 7.2 and let the chlorine level drop below 2 ppm. 2. For pool water discoloration, pour 150 g of METABAN per 10,000 L of pool water directly over the swimming pool surface. For stain removal, proceed to # 3. 3. Brush affected areas. 4. Add 150 g of MET ABAN per 10,000 L of pool water to a pail of water and apply the concentrated solution along the pool walls and/or in areas where staining is present. Where stains are most prevalent directly brush with the product. 5. Severe staining of surfaces may require up to 300 g of METABAN per 10,000 L of pool water. 6. Allow the circulation system to run continuously for 24 hours. 7. After 24 hours, adjust pH between 7.2 - 7.8 and alkalinity between 80 - 120 ppm. 8. Do not superchlorinate water for at least 72 hours. 9. Continue to use METABAN on a weekly basis to prevent the reoccurrence of staining of swimming pool surfaces or water discoloration.
Buy30-21335-11
Skin Silk - 2 kg
Item ID: (30-21045-12) Brand: IPG
SKIN SILK softens water
and improves bather comfort.
It is a selected pool product combined with aromatherapy so as to enhance water quality.
SKIN SILK is compatible with pool sanitizing chemicals and increases their efficiency.
Balanced pH formula that won't affect pool water parameters.
Makes pool water crystal clear.
AROMATHERAPY.
Increases sanitizer efficiency.
Produces water softness.
Application
1. For initial treatment in early season add 1. 5 kg of SKIN SILK per 10,000 L of pool water. Add the required quantity in 2 applications at 4-hour intervals. 2. Sprinkle lightly above the water return, not into the skimmer. 3. To adjust the SKIN SILK level during the season (mid-July), add 1.5 kg of SKIN SILK per 10,000 L of pool water. Add the required quantity in 2 applications at 4-hour intervals. 4. Check water pH after application and adjust between 7.2 and 7.8 if necessary.
Buy30-21045-12
Skin Silk - 7 kg
Item ID: (30-21045-07) Brand: IPG
SKIN SILK softens water and improves bather comfort.
It is a selected pool product combined with aromatherapy so as to enhance water quality.
SKIN SILK is compatible with pool sanitizing chemicals and increases their efficiency.
Balanced pH formula that won't affect pool water parameters.
Makes pool water crystal clear.
AROMATHERAPY.
Increases sanitizer efficiency.
Produces water softness.
Application
1. For initial treatment in early season add 1. 5 kg of SKIN SILK per 10,000 L of pool water. Add the required quantity in 2 applications at 4-hour intervals. 2. Sprinkle lightly above the water return, not into the skimmer. 3. To adjust the SKIN SILK level during the season (mid-July), add 1.5 kg of SKIN SILK per 10,000 L of pool water. Add the required quantity in 2 applications at 4-hour intervals. 4. Check water pH after application and adjust between 7.2 and 7.8 if necessary.
Mermaid has been selling swimming pools and hot tubs in the national capital region for over 50 years. During those five decades we've installed over 40,000 pools and hot tubs – beautiful pools and hot tubs that give our clients countless hours of fun and relaxation.
Plus we provide swimming pool and hot tub service and repair to ensure our customers continue to enjoy their investment. We are one of Ottawa’s largest sources for pool and hot tub accessories and supplies including a wide range of pool liners and pool and spa covers.
If you’re looking for Ottawa swimming pool and hot tub experts, you have come to the right place.
pool & spa supplies
Pool & Hot Tub filters Ottawa
Pool & Hot Tub pumps Ottawa
Pool & Hot Tub covers Ottawa
Pool & Hot Tub chemicals Ottawa
Pool slides Ottawa
Pool renovations Ottawa
Pool liners Ottawa
and much much more....
Share with a friend
